Key takeaways
- Typical cost in George West: $1,200–$2,700 (per installed panel); national range $1,300–$3,000.
- Biggest local factors: long, hot cooling season, flooding and high humidity.
- How long it takes: Most panel upgrades take about 4–8 hours of labor, plus utility scheduling.
- Permits: A permit is required, typically $50–$300; the electrician usually pulls it.
- Best timing: Upgrade before summer, when AC loads are highest.
- Before you hire: get at least three written, itemized quotes from licensed, insured Texas contractors.
How much does electrical panel upgrade cost in George West, TX?
An electrical panel upgrade typically costs $1,300–$3,000, with an average around $2,150. Amperage, meter and service changes, and subpanels drive the price. Texas prices run 11% below the U.S. average, so a typical George West job lands around $1,200–$2,700. Local labor rates, permit fees and your home's specifics move the final number.
| Item | Typical cost | Notes |
|---|---|---|
| 100-amp panel installed | $800–$1,500 | |
| 150-amp panel installed | $1,300–$1,600 | |
| 200-amp panel / 100→200 amp upgrade | $1,300–$3,000 | |
| 400-amp service | $2,000–$4,000 | |
| Meter box | $200–$800 | Must match the new service |
| Subpanel | $400–$1,750 | |
| Permit | $50–$300 | Electrician usually pulls it |
In a smaller community like George West, some specialists travel in from nearby cities and may add a trip charge. Ask whether travel is included, and consider bundling projects.
How we calculate costs
National ranges come from published cost surveys (cited below). Local estimates apply an approximate state cost index. Read our methodology.
Electrical Panel Upgrade cost questions for George West, TX
- What is the cost of 100-amp panel installed in George West, TX? The typical cost of 100-amp panel installed in George West, TX is $710–$1,300, adjusted for Texas prices (national $800–$1,500).
- What is the cost of 150-amp panel installed in George West, TX? The typical cost of 150-amp panel installed in George West, TX is $1,200–$1,400, adjusted for Texas prices (national $1,300–$1,600).
- What is the cost of 200-amp panel / 100→200 amp upgrade in George West, TX? The typical cost of 200-amp panel / 100→200 amp upgrade in George West, TX is $1,200–$2,700, adjusted for Texas prices (national $1,300–$3,000).
- What is the cost of 400-amp service in George West, TX? The typical cost of 400-amp service in George West, TX is $1,800–$3,600, adjusted for Texas prices (national $2,000–$4,000).
- What is the cost of meter box in George West, TX? The typical cost of meter box in George West, TX is $180–$710, adjusted for Texas prices (national $200–$800). Must match the new service.
- What is the cost of subpanel in George West, TX? The typical cost of subpanel in George West, TX is $360–$1,600, adjusted for Texas prices (national $400–$1,750).
- What is the cost of permit in George West, TX? The typical cost of permit in George West, TX is $40–$270, adjusted for Texas prices (national $50–$300). Electrician usually pulls it.
- What is the cost of move the panel in George West, TX? The typical cost of move the panel in George West, TX is $710–$2,700, adjusted for Texas prices (national $800–$3,000).
- What is the cost of main breaker replacement in George West, TX? The typical cost of main breaker replacement in George West, TX is $180–$270, adjusted for Texas prices (national $200–$300). $500–$2,000 if the bus bar is damaged.
- What is the cost of AFCI/GFCI breakers in George West, TX? The typical cost of AFCI/GFCI breakers in George West, TX is $30–$50 each, adjusted for Texas prices (national $35–$60 each). Often required by code.
What affects electrical panel upgrade in George West
George West has hot, humid summers and mild winters. Upgrade before summer, when AC loads are highest.
Signs you need a panel upgrade
- Breakers trip often
- Lights flicker or dim when appliances run
- You rely on power strips or can't run appliances together
- The panel buzzes, feels hot or smells burnt
- Rust or visible damage
- A Federal Pacific or Zinsco panel, or plans for an EV charger or heat pump
Common questions about electrical panel upgrade in George West
How much does an electrical panel upgrade cost in George West, TX?
Most panel upgrades cost about $1,200–$2,700 in George West, TX. A 100-to-200-amp upgrade typically runs $1,300–$3,000 nationally.
Do I need a 200 amp panel?
Most modern homes with central air, electric appliances or an EV charger are planned around 200 amps. A load calculation tells you for sure.
Is a Federal Pacific or Zinsco panel dangerous?
Both are widely flagged as outdated, and many electricians recommend replacing them.
How much does a subpanel cost?
A subpanel typically costs $400–$1,750 installed and can add circuits for a garage, addition or EV charger.
Timeline, permits and DIY in George West
How long it takes
Most panel upgrades take about 4–8 hours of labor, plus utility scheduling.
Permits
A permit is required, typically $50–$300; the electrician usually pulls it. Check with the George West building department for local rules.
DIY or hire a pro?
Not a DIY job: a licensed electrician must do the work and coordinate with the utility.
Questions to ask George West contractors
Ask every bidder the same questions so you can compare quotes apples to apples.
- Did you do a load calculation for my home?
- Does the quote include the meter, permit and utility coordination?
- Which breakers will be AFCI or GFCI to meet code?
- Will the power be off, and for how long?
Maintenance that prevents costly repairs
- Have the panel inspected if breakers trip often
- Never ignore buzzing or burning smells
- Label circuits clearly
How to hire for electrical panel upgrade in George West
- Use a licensed, insured electrician.
- Ask for a load calculation to size the new service.
- Confirm the permit, inspection and utility coordination are included.
- Get the warranty for parts and labor in writing.
Electrical Panel Upgrade in George West: FAQs
How much does an electrical panel upgrade cost in George West, TX?
Nationally, most upgrades cost $1,300–$3,000. Local permit fees and utility requirements change the final price.
Do I need a permit for a panel upgrade in George West?
Yes. A licensed electrician typically pulls the permit and coordinates with the utility.
Will I need a panel upgrade to add a heat pump in George West?
Possibly. Ask for a load calculation; many older homes need 200-amp service for heat pumps and EV chargers.
How much does electrical panel upgrade cost in George West compared to the national average?
With Texas's regional cost index of 0.89, expect roughly $1,200–$2,700 in George West, versus $1,300–$3,000 nationally.
How long does electrical panel upgrade take in George West?
Most panel upgrades take about 4–8 hours of labor, plus utility scheduling. Permit and inspection scheduling in George West can add a few days.
Do I need a permit for electrical panel upgrade in George West?
A permit is required, typically $50–$300; the electrician usually pulls it. Confirm with the George West or county building department.
Which George West ZIP codes does this guide cover?
This guide applies to George West ZIP codes 78022, 78350, plus the surrounding area.
Electrical Panel Upgrade near George West
10 mi away · pop. 1,971Beeville, TX
23 mi away · pop. 13,277Mathis, TX
24 mi away · pop. 5,037Tilden, TX
28 mi away · pop. 261Orange Grove, TX
28 mi away · pop. 1,334Kenedy, TX
37 mi away · pop. 3,421San Diego, TX
40 mi away · pop. 4,368Alice, TX
40 mi away · pop. 19,408Karnes City, TX
40 mi away · pop. 3,371
Other home services in George West
Sources: This Old House — Cost to upgrade an electrical panel · Angi — Cost to upgrade an electrical panel. Ranges are rounded estimates; see our editorial policy.
Local risk factors reflect general Texas climate patterns; check FEMA's National Risk Index for county-level ratings. Local estimates apply an approximate regional cost index to national ranges.