Key takeaways
- Typical cost in Marble Falls: $1,200–$2,700 (per installed panel); national range $1,300–$3,000.
- Biggest local factors: long, hot cooling season, flooding and high humidity.
- How long it takes: Most panel upgrades take about 4–8 hours of labor, plus utility scheduling.
- Permits: A permit is required, typically $50–$300; the electrician usually pulls it.
- Best timing: Upgrade before summer, when AC loads are highest.
- Before you hire: get at least three written, itemized quotes from licensed, insured Texas contractors.
How much does electrical panel upgrade cost in Marble Falls, TX?
An electrical panel upgrade typically costs $1,300–$3,000, with an average around $2,150. Amperage, meter and service changes, and subpanels drive the price. Texas prices run 11% below the U.S. average, so a typical Marble Falls job lands around $1,200–$2,700. Local labor rates, permit fees and your home's specifics move the final number.
| Item | Typical cost | Notes |
|---|---|---|
| 100-amp panel installed | $800–$1,500 | |
| 150-amp panel installed | $1,300–$1,600 | |
| 200-amp panel / 100→200 amp upgrade | $1,300–$3,000 | |
| 400-amp service | $2,000–$4,000 | |
| Meter box | $200–$800 | Must match the new service |
| Subpanel | $400–$1,750 | |
| Permit | $50–$300 | Electrician usually pulls it |
In a smaller community like Marble Falls, some specialists travel in from nearby cities and may add a trip charge. Ask whether travel is included, and consider bundling projects.
How we calculate costs
National ranges come from published cost surveys (cited below). Local estimates apply an approximate state cost index. Read our methodology.
Electrical Panel Upgrade cost questions for Marble Falls, TX
- What is the cost of 100-amp panel installed in Marble Falls, TX? The typical cost of 100-amp panel installed in Marble Falls, TX is $710–$1,300, adjusted for Texas prices (national $800–$1,500).
- What is the cost of 150-amp panel installed in Marble Falls, TX? The typical cost of 150-amp panel installed in Marble Falls, TX is $1,200–$1,400, adjusted for Texas prices (national $1,300–$1,600).
- What is the cost of 200-amp panel / 100→200 amp upgrade in Marble Falls, TX? The typical cost of 200-amp panel / 100→200 amp upgrade in Marble Falls, TX is $1,200–$2,700, adjusted for Texas prices (national $1,300–$3,000).
- What is the cost of 400-amp service in Marble Falls, TX? The typical cost of 400-amp service in Marble Falls, TX is $1,800–$3,600, adjusted for Texas prices (national $2,000–$4,000).
- What is the cost of meter box in Marble Falls, TX? The typical cost of meter box in Marble Falls, TX is $180–$710, adjusted for Texas prices (national $200–$800). Must match the new service.
- What is the cost of subpanel in Marble Falls, TX? The typical cost of subpanel in Marble Falls, TX is $360–$1,600, adjusted for Texas prices (national $400–$1,750).
- What is the cost of permit in Marble Falls, TX? The typical cost of permit in Marble Falls, TX is $40–$270, adjusted for Texas prices (national $50–$300). Electrician usually pulls it.
- What is the cost of move the panel in Marble Falls, TX? The typical cost of move the panel in Marble Falls, TX is $710–$2,700, adjusted for Texas prices (national $800–$3,000).
- What is the cost of main breaker replacement in Marble Falls, TX? The typical cost of main breaker replacement in Marble Falls, TX is $180–$270, adjusted for Texas prices (national $200–$300). $500–$2,000 if the bus bar is damaged.
- What is the cost of AFCI/GFCI breakers in Marble Falls, TX? The typical cost of AFCI/GFCI breakers in Marble Falls, TX is $30–$50 each, adjusted for Texas prices (national $35–$60 each). Often required by code.
What affects electrical panel upgrade in Marble Falls
Marble Falls has hot, humid summers and mild winters. Upgrade before summer, when AC loads are highest.
Signs you need a panel upgrade
- Breakers trip often
- Lights flicker or dim when appliances run
- You rely on power strips or can't run appliances together
- The panel buzzes, feels hot or smells burnt
- Rust or visible damage
- A Federal Pacific or Zinsco panel, or plans for an EV charger or heat pump
Common questions about electrical panel upgrade in Marble Falls
How much does an electrical panel upgrade cost in Marble Falls, TX?
Most panel upgrades cost about $1,200–$2,700 in Marble Falls, TX. A 100-to-200-amp upgrade typically runs $1,300–$3,000 nationally.
Do I need a 200 amp panel?
Most modern homes with central air, electric appliances or an EV charger are planned around 200 amps. A load calculation tells you for sure.
Is a Federal Pacific or Zinsco panel dangerous?
Both are widely flagged as outdated, and many electricians recommend replacing them.
How much does a subpanel cost?
A subpanel typically costs $400–$1,750 installed and can add circuits for a garage, addition or EV charger.
Timeline, permits and DIY in Marble Falls
How long it takes
Most panel upgrades take about 4–8 hours of labor, plus utility scheduling.
Permits
A permit is required, typically $50–$300; the electrician usually pulls it. Check with the Marble Falls building department for local rules.
DIY or hire a pro?
Not a DIY job: a licensed electrician must do the work and coordinate with the utility.
Questions to ask Marble Falls contractors
Ask every bidder the same questions so you can compare quotes apples to apples.
- Did you do a load calculation for my home?
- Does the quote include the meter, permit and utility coordination?
- Which breakers will be AFCI or GFCI to meet code?
- Will the power be off, and for how long?
Maintenance that prevents costly repairs
- Have the panel inspected if breakers trip often
- Never ignore buzzing or burning smells
- Label circuits clearly
How to hire for electrical panel upgrade in Marble Falls
- Use a licensed, insured electrician.
- Ask for a load calculation to size the new service.
- Confirm the permit, inspection and utility coordination are included.
- Get the warranty for parts and labor in writing.
Electrical Panel Upgrade in Marble Falls: FAQs
How much does an electrical panel upgrade cost in Marble Falls, TX?
Nationally, most upgrades cost $1,300–$3,000. Local permit fees and utility requirements change the final price.
Do I need a permit for a panel upgrade in Marble Falls?
Yes. A licensed electrician typically pulls the permit and coordinates with the utility.
Will I need a panel upgrade to add a heat pump in Marble Falls?
Possibly. Ask for a load calculation; many older homes need 200-amp service for heat pumps and EV chargers.
How much does electrical panel upgrade cost in Marble Falls compared to the national average?
With Texas's regional cost index of 0.89, expect roughly $1,200–$2,700 in Marble Falls, versus $1,300–$3,000 nationally.
How long does electrical panel upgrade take in Marble Falls?
Most panel upgrades take about 4–8 hours of labor, plus utility scheduling. Permit and inspection scheduling in Marble Falls can add a few days.
Do I need a permit for electrical panel upgrade in Marble Falls?
A permit is required, typically $50–$300; the electrician usually pulls it. Confirm with the Marble Falls or county building department.
Which Marble Falls ZIP codes does this guide cover?
This guide applies to Marble Falls ZIP codes 78654, plus the surrounding area.
Electrical Panel Upgrade near Marble Falls
2 mi away · pop. 1,872Cottonwood Shores, TX
3 mi away · pop. 1,158Horseshoe Bay, TX
6 mi away · pop. 3,560Granite Shoals, TX
7 mi away · pop. 5,071Kingsland, TX
11 mi away · pop. 6,030Burnet, TX
13 mi away · pop. 6,239Buchanan Dam, TX
15 mi away · pop. 1,519Bertram, TX
17 mi away · pop. 1,390Briarcliff, TX
18 mi away · pop. 1,510
Other home services in Marble Falls
Sources: This Old House — Cost to upgrade an electrical panel · Angi — Cost to upgrade an electrical panel. Ranges are rounded estimates; see our editorial policy.
Local risk factors reflect general Texas climate patterns; check FEMA's National Risk Index for county-level ratings. Local estimates apply an approximate regional cost index to national ranges.