Key takeaways
- Typical cost in Evanston: $1,200–$2,700 (per installed panel); national range $1,300–$3,000.
- Biggest local factors: long heating season.
- How long it takes: Most panel upgrades take about 4–8 hours of labor, plus utility scheduling.
- Permits: A permit is required, typically $50–$300; the electrician usually pulls it.
- Best timing: Upgrade before adding electric heat or a heat pump for winter.
- Before you hire: get at least three written, itemized quotes from licensed, insured Wyoming contractors.
How much does electrical panel upgrade cost in Evanston, WY?
An electrical panel upgrade typically costs $1,300–$3,000, with an average around $2,150. Amperage, meter and service changes, and subpanels drive the price. Wyoming prices run 9% below the U.S. average, so a typical Evanston job lands around $1,200–$2,700. Local labor rates, permit fees and your home's specifics move the final number.
| Item | Typical cost | Notes |
|---|---|---|
| 100-amp panel installed | $800–$1,500 | |
| 150-amp panel installed | $1,300–$1,600 | |
| 200-amp panel / 100→200 amp upgrade | $1,300–$3,000 | |
| 400-amp service | $2,000–$4,000 | |
| Meter box | $200–$800 | Must match the new service |
| Subpanel | $400–$1,750 | |
| Permit | $50–$300 | Electrician usually pulls it |
In a smaller community like Evanston, some specialists travel in from nearby cities and may add a trip charge. Ask whether travel is included, and consider bundling projects.
How we calculate costs
National ranges come from published cost surveys (cited below). Local estimates apply an approximate state cost index. Read our methodology.
Electrical Panel Upgrade cost questions for Evanston, WY
- What is the cost of 100-amp panel installed in Evanston, WY? The typical cost of 100-amp panel installed in Evanston, WY is $730–$1,400, adjusted for Wyoming prices (national $800–$1,500).
- What is the cost of 150-amp panel installed in Evanston, WY? The typical cost of 150-amp panel installed in Evanston, WY is $1,200–$1,500, adjusted for Wyoming prices (national $1,300–$1,600).
- What is the cost of 200-amp panel / 100→200 amp upgrade in Evanston, WY? The typical cost of 200-amp panel / 100→200 amp upgrade in Evanston, WY is $1,200–$2,700, adjusted for Wyoming prices (national $1,300–$3,000).
- What is the cost of 400-amp service in Evanston, WY? The typical cost of 400-amp service in Evanston, WY is $1,800–$3,600, adjusted for Wyoming prices (national $2,000–$4,000).
- What is the cost of meter box in Evanston, WY? The typical cost of meter box in Evanston, WY is $180–$730, adjusted for Wyoming prices (national $200–$800). Must match the new service.
- What is the cost of subpanel in Evanston, WY? The typical cost of subpanel in Evanston, WY is $360–$1,600, adjusted for Wyoming prices (national $400–$1,750).
- What is the cost of permit in Evanston, WY? The typical cost of permit in Evanston, WY is $50–$270, adjusted for Wyoming prices (national $50–$300). Electrician usually pulls it.
- What is the cost of move the panel in Evanston, WY? The typical cost of move the panel in Evanston, WY is $730–$2,700, adjusted for Wyoming prices (national $800–$3,000).
- What is the cost of main breaker replacement in Evanston, WY? The typical cost of main breaker replacement in Evanston, WY is $180–$270, adjusted for Wyoming prices (national $200–$300). $500–$2,000 if the bus bar is damaged.
- What is the cost of AFCI/GFCI breakers in Evanston, WY? The typical cost of AFCI/GFCI breakers in Evanston, WY is $30–$50 each, adjusted for Wyoming prices (national $35–$60 each). Often required by code.
What affects electrical panel upgrade in Evanston
Evanston has long, very cold winters. Upgrade before adding electric heat or a heat pump for winter.
Signs you need a panel upgrade
- Breakers trip often
- Lights flicker or dim when appliances run
- You rely on power strips or can't run appliances together
- The panel buzzes, feels hot or smells burnt
- Rust or visible damage
- A Federal Pacific or Zinsco panel, or plans for an EV charger or heat pump
Common questions about electrical panel upgrade in Evanston
How much does an electrical panel upgrade cost in Evanston, WY?
Most panel upgrades cost about $1,200–$2,700 in Evanston, WY. A 100-to-200-amp upgrade typically runs $1,300–$3,000 nationally.
Do I need a 200 amp panel?
Most modern homes with central air, electric appliances or an EV charger are planned around 200 amps. A load calculation tells you for sure.
Is a Federal Pacific or Zinsco panel dangerous?
Both are widely flagged as outdated, and many electricians recommend replacing them.
How much does a subpanel cost?
A subpanel typically costs $400–$1,750 installed and can add circuits for a garage, addition or EV charger.
Timeline, permits and DIY in Evanston
How long it takes
Most panel upgrades take about 4–8 hours of labor, plus utility scheduling.
Permits
A permit is required, typically $50–$300; the electrician usually pulls it. Check with the Evanston building department for local rules.
DIY or hire a pro?
Not a DIY job: a licensed electrician must do the work and coordinate with the utility.
Questions to ask Evanston contractors
Ask every bidder the same questions so you can compare quotes apples to apples.
- Did you do a load calculation for my home?
- Does the quote include the meter, permit and utility coordination?
- Which breakers will be AFCI or GFCI to meet code?
- Will the power be off, and for how long?
Maintenance that prevents costly repairs
- Have the panel inspected if breakers trip often
- Never ignore buzzing or burning smells
- Label circuits clearly
How to hire for electrical panel upgrade in Evanston
- Use a licensed, insured electrician.
- Ask for a load calculation to size the new service.
- Confirm the permit, inspection and utility coordination are included.
- Get the warranty for parts and labor in writing.
Electrical Panel Upgrade in Evanston: FAQs
How much does an electrical panel upgrade cost in Evanston, WY?
Nationally, most upgrades cost $1,300–$3,000. Local permit fees and utility requirements change the final price.
Do I need a permit for a panel upgrade in Evanston?
Yes. A licensed electrician typically pulls the permit and coordinates with the utility.
Will I need a panel upgrade to add a heat pump in Evanston?
Possibly. Ask for a load calculation; many older homes need 200-amp service for heat pumps and EV chargers.
How much does electrical panel upgrade cost in Evanston compared to the national average?
With Wyoming's regional cost index of 0.91, expect roughly $1,200–$2,700 in Evanston, versus $1,300–$3,000 nationally.
How long does electrical panel upgrade take in Evanston?
Most panel upgrades take about 4–8 hours of labor, plus utility scheduling. Permit and inspection scheduling in Evanston can add a few days.
Do I need a permit for electrical panel upgrade in Evanston?
A permit is required, typically $50–$300; the electrician usually pulls it. Confirm with the Evanston or county building department.
Which Evanston ZIP codes does this guide cover?
This guide applies to Evanston ZIP codes 82930, 82931, plus the surrounding area.
Electrical Panel Upgrade near Evanston
30 mi away · pop. 462Mountain View, WY
32 mi away · pop. 1,294Coalville, UT
33 mi away · pop. 1,431Lyman, WY
35 mi away · pop. 2,074Morgan, UT
40 mi away · pop. 4,049Oakley, UT
42 mi away · pop. 1,591Kemmerer, WY
42 mi away · pop. 2,739Mountain Green, UT
44 mi away · pop. 2,309Wolf Creek, UT
45 mi away · pop. 1,336
Other home services in Evanston
Sources: This Old House — Cost to upgrade an electrical panel · Angi — Cost to upgrade an electrical panel. Ranges are rounded estimates; see our editorial policy.
Local risk factors reflect general Wyoming climate patterns; check FEMA's National Risk Index for county-level ratings. Local estimates apply an approximate regional cost index to national ranges.